Short Answer
Steam consumption for process heating is found by dividing the heat a process needs by the useful heat that each kilogram of steam can release. That useful heat comes from the enthalpy drop between the steam supplied (inlet) and the condensate leaving the process (outlet). Once both enthalpies are reviewed on a common basis and transfer losses are counted once, the required steam mass flow follows directly from simple division.
The enthalpy-drop method
Enthalpy, written h and measured in kilojoules per kilogram (kJ/kg), is the property used to track the energy carried by flowing water and steam, and it is tabulated for every practical pressure and temperature in steam tables. Steam arrives at the process with a large enthalpy; as it condenses—and, in some equipment, cools further as subcooled condensate—it gives up heat and leaves at a much lower enthalpy. The difference between the two states is the heat actually available to the process.
One scenario calculator expresses the calculation in exactly these terms: usable kWh per kilogram = (steam inlet enthalpy − outlet condensate enthalpy) × transfer-effectiveness fraction ÷ 3,600, with an illustrative default of 0.5 kWh per kilogram of steam (Case & Contrast, Process Steam Consumption Scenario Calculator). Each element matters:
- Enthalpy drop (kJ/kg). The reviewed inlet steam enthalpy minus the reviewed outlet condensate enthalpy. Both values must refer to the same reference datum—steam tables share one basis, and mixing values from inconsistent assumptions is the main accuracy trap the calculator warns about.
- Transfer-effectiveness fraction. A single factor between 0 and 1 covering imperfect heat transfer and end-use losses. It counts transfer losses once; layering separate loss percentages on top would double-count them.
- Division by 3,600. One kilowatt-hour is 3,600 kilojoules, so dividing kJ/kg by 3,600 converts the result to kWh/kg. Once the result is in kWh/kg, the remaining arithmetic is trivial.
Setting the two enthalpies
Inlet steam enthalpy
For saturated steam, the inlet enthalpy is read from steam tables at the supply pressure. Steam tables are indexed by absolute pressure, so a gauge reading has 1.01325 bar added before lookup—a convention that calculator guidance for steam work also emphasises (CodingAce, Steam Consumption Calculator). Steam quality matters too: dry saturated steam corresponds to a quality of 1.0, while wet steam with a quality below 1.0 carries less energy per kilogram because part of the mass is already liquid. Superheated steam has a higher inlet enthalpy, but the extra sensible heat only helps if it actually transfers to the process.
Outlet condensate enthalpy
The condensate enthalpy depends on the state in which liquid leaves the process. Hot condensate retains considerable energy—water at about 90 °C holds roughly 377 kJ/kg—so the hotter the condensate leaving, the less heat each kilogram of steam has delivered to the product. Deliberately subcooling the condensate raises the delivered heat per kilogram. At an indirect consumer such as a heat exchanger the condensate normally returns to the steam circuit; at a direct consumer such as an autoclave, steam contacts the product and leaves as condensate mixed with (or in) the product. That changes the accounting in two ways: the condensate enthalpy is still the reference for the enthalpy drop, and the consumed water must be replaced with treated make-up water that is deaerated before re-entering the circuit (Bosch steam boiler planning).
From process duty to steam mass flow
- Calculate the process duty in kW. For a product stream, duty is the product flow (kg/h) multiplied by its specific heat (kJ/kg·K; for water, about 4.2) and its temperature rise (K), divided by 3,600 to convert kJ/h to kW; add latent-heat terms for evaporation, melting or reactions where they apply (Helper food process steam demand planning guide).
- Review the two enthalpies for the actual operating states, on the same datum, in kJ/kg.
- Choose one effectiveness factor reflecting end-use transfer performance, and compute the usable heat in kWh/kg using the formula above.
- Divide. Because 1 kW sustained for one hour is exactly 1 kWh, the steam mass flow in kg/h is simply the duty in kW divided by the usable heat in kWh/kg.
- Add the adders. Warm-up loads, distribution losses and other consumers are calculated separately and added on top; they are not absorbed into the effectiveness factor.
- Combine users. Where several consumers share a boiler, each is tabulated with its minimum and maximum output and the results are summed, grouped by time and by pressure level.
Worked examples
Example A — a batch case (hypothetical, using the calculator’s illustrative defaults). Suppose the usable heat works out to 0.5 kWh per kilogram of steam, and a batch requires 100 kWh of useful process heat. The modeled steam mass is 100 ÷ 0.5 = 200 kg—the very pair of figures the scenario calculator displays as its example result. The defaults are illustrative; a real assessment should use reviewed enthalpies and a site-specific effectiveness.
Example B — a continuous case (sample output from a published calculator). An online steam-consumption calculator works from heat load, supply pressure, quality, condensate return temperature and an overall efficiency, and its sample table reports these estimates:
| Heat load | Pressure (bar g) | Quality | Condensate return | Efficiency | Steam estimate |
|---|---|---|---|---|---|
| 500 kW | 6 | 1.0 | 90 °C | 0.90 | about 900 kg/h (typical) |
| 250 kW | 3 | 0.98 | 80 °C | 0.85 | about 500 kg/h |
The enthalpy method explains the magnitude of the first row. At 6 bar g the supply is near 7 bar absolute, where dry saturated steam carries roughly 2,770 kJ/kg and the latent (condensing) heat alone is about 2,075 kJ/kg. Full-drop accounting with subcooling to 90 °C gives about 0.6 kWh/kg after the 0.90 efficiency; counting only the condensing heat gives closer to 0.5 kWh/kg. For a 500 kW duty these assumptions span roughly 840–960 kg/h, which brackets the calculator’s ≈900 kg/h estimate. The point is sensitivity, not precision: small changes in the reviewed states and the efficiency assumption move the answer noticeably, which is why scenario-style calculation is useful.
What the boiler must supply besides the process load
The enthalpy calculation gives consumption for one consumer’s steady heating duty. Boiler-output planning adds the rest. Bosch’s boiler planning guidance distinguishes the consumer categories that should be recorded and summed, each with minimum and maximum output:
- Direct consumers, where steam touches the product and the condensate leaves the system with it, creating treated make-up water demand.
- Indirect consumers, such as heat exchangers, whose condensate can return to the circuit.
- Expansion steam losses, for example flash steam vented at an unpressurised condensate tank.
- Heat losses in the steam pipes.
- The boiler system’s own use, such as heat-up steam for the feed water vessel.
Food-industry planning guidance reaches the same conclusion from the demand side: convert the product duty into a steam estimate with the enthalpy method, then add separately calculated warm-up and loss loads, and combine all users by time and by pressure level. Neither the boiler nor the distribution piping should be sized from the continuous product load alone, because warm-up and start-up demands can dominate at the moment they occur even if they are brief on average.
Common mistakes
- Mixed datums. Taking the steam enthalpy from one basis and the condensate enthalpy from another inflates the drop and undercounts steam; use one consistent, reviewed pair of values.
- Double-counting losses. The transfer-effectiveness fraction already absorbs end-use losses; distribution losses and warm-up belong in separate adders, each counted once.
- Wet steam treated as dry. Reading dry-saturated enthalpy for a supply with quality below 1.0 overstates the available heat.
- Gauge versus absolute pressure. Steam tables require absolute pressure; omitting the 1.01325 bar addition shifts every lookup.
- Ignoring condensate temperature. It changes both the delivered heat per kilogram at the point of use and the energy carried back toward the boiler house.
- Overlooking consumed water. Direct injection consumes water as well as heat; make-up must be treated and deaerated before re-use.
- Sizing from steady duty alone. The continuous product load omits warm-up, distribution losses, expansion steam and boiler own use.
Practical takeaways
The working sequence is short: review the inlet steam and outlet condensate enthalpies on a common datum, multiply their difference by a single effectiveness factor, divide by 3,600 to obtain kWh/kg, and divide the reviewed process duty by that value to get kg/h. Add warm-up loads, distribution losses, expansion steam and boiler own-use separately, combine all consumers by time and pressure level, and only then compare the result against boiler capacity. Working the numbers as a scenario—in a spreadsheet or a dedicated calculator—makes it easy to see which assumption drives the answer.
FAQ
Why is the enthalpy difference divided by 3,600?
Enthalpies are tabulated in kJ/kg, and one kilowatt-hour equals 3,600 kJ. Dividing by 3,600 converts the drop to kWh/kg so that a duty in kW, divided by kWh/kg, gives steam mass flow directly in kg/h.
Does returning hotter condensate reduce steam consumption?
Not at the point of use: hotter condensate leaving the process means each kilogram of steam delivered less heat, so more steam is needed for the same duty. Downstream, hotter return does save fuel at the boiler because less energy is needed to bring feedwater up to boil. The two balances are separate and should not be mixed.
Which pressure should be used when reading steam tables?
Absolute pressure. Add 1.01325 bar to a gauge reading before lookup, as steam-consumption calculator guidance emphasises, because tables are indexed by absolute rather than gauge pressure.
How are several steam consumers combined for boiler planning?
Record each consumer with its minimum and maximum output, distinguishing direct from indirect, then add steam pipe heat losses, expansion steam losses and the boiler system's own use. Group the totals by time and by pressure level before sizing.
Why might calculated steam use differ from what a meter shows?
The calculation relies on reviewed enthalpies, steam quality, condensate return temperature and a single effectiveness factor, all of which are estimates. Real systems add start-up behaviour, insulation variation and leakage, so calculated values are best treated as planning figures to be checked against measured consumption.
Leave a Reply